Why is my dog watch fence beeping

If there is a break in the boundary wire, you will hear an alarm coming from your DogWatch transmitter. If there is a wire break, the signal is interrupted and the fence will not work. If you hear this alarm, we recommend contacting your local DogWatch Dealer as soon as possible.

Why is my pet safe transmitter beeping?

The transmitter box starts to beep to notify you that your dog left the yard. If there is a break in the fence, the transmitter box will beep nonstop until the break is located and repaired. Since the fence line is invisible, the level of difficultly in locating the break in the fence increases.

How do you reset an invisible fence?

Resetting the system can be as simple as replacing the batteries in your transmitter. Bring your dog inside, and turn off the power to the fence. Unplug the transmitter. Look for metal objects around or on top of the fence.

Why is my dog's shock collar beeping?

Please restart the collar by simply by taking out the battery than put it back. Try to use the collar on low sensitivity setting first then change the sensitivity according to the dog’s barking. If still you see the continuous beeping, please put a new battery. … It’s because the battery is low.

How do I check the batteries in my invisible fence collar?

Insert the coin in the slot on top of the Power Cap unit and turn it 45 degrees counter-clockwise. Do not push down while turning. The Power Cap unit will rotate while the spring inside will push the Power Cap battery out of the Computer Collar unit battery chamber.

Why is my petsafe collar beeping but not shocking?

Touch both points on the collar while it is ticking or beeping. If you do not feel a shock, then there may be a problem with the receiver collar. Make sure you touch both points on the receiver at the same time when you hear the collar beeping. It will tell you definitively that the fence is or is not working.

How do you find a break in an electric dog fence?

Another simple solution to test if you have a invisible dog fence wire break is to use an ohm meter and check the continuity on the disconnected wires. If there is zero resistance on the wires then you have a wire break.

How do you reset a shock collar on a dog?

Press and hold the power button for 10 seconds to reset the collar. The light turns red and the collar turns off. Continue holding the button. The collar flashes green and beeps five times to indicate that the PIN has been reset.

How do you reset an electric dog collar?

Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5 times. You may need to hold both units 2-3 feet from each other before this occurs. Once the Receiver Indicator Light has flashed 5 times, the Collar Receiver has been reset and will begin flashing as normal.

How do I know if my shock collar is working?

Touch both points on the collar while it is ticking or beeping. If you do not feel a shock, then there may be a problem with the receiver collar. Make sure you touch both points on the receiver at the same time when you hear the collar beeping. It will tell you definitively that the fence is or is not working.

Article first time published on

Why is my invisible fence unit beeping?

If your Invisible Fence control panel is beeping every second, the most likely issue is that you have a wire break somewhere on your property. … If your Invisible Fence control panel is beeping with a lengthy pause between each beep, it’s possible your backup battery unit needs to be replaced.

Why is my dog invisible fence collar blinking green?

The status light will double flash green every 30 seconds during the 24-hour period after the dog has entered the boundary area. This feature monitors the voltage level of the battery. … If your light flashes double red, this indicates that your battery is low and your pet has challenged the dog containment system.

Do invisible fence batteries expire?

How often should I replace the battery in my Invisible Fence Computer Collar? We recommend changing the battery every 3 months – it’s the safest, easiest and most reliable way to guarantee your pet’s safety 100% of the time.

Why is my dog invisible fence collar blinking red?

Why is my Invisible Fence collar blinking red? If you have started to see a red flashing light on your pet’s Computer Collar unit, your Power Cap battery may need to be replaced. You can order replacement batteries online, from your local dealer, or by calling 1-800-824-3647.

What frequency do invisible fences use?

Invisible Fence compatible collar for fences running on the 10k frequency.

How can you tell where a wire is broken?

Place the black end of the multimeter into the round ground port of the device. Place the red in the smaller of the two slotted ports on the device. Make sure the leads are connected to metal in order for the multimeter to work properly. If the resistance is zero, you’ve found the break.

Which electric dog fence is best?

RankThe FenceBest For1SpotOn Virtual Smart FenceBest Overall2Halo CollarRunner Up3Wagz® Freedom CollarBest Value4PetSafe Stay & PlayBest Wireless Base Station

How do you test a dog's extreme fence collar?

How are you testing the collar? To test it properly, you must approach the fence in one place, then go back into the center of the yard and walk back out to another spot. Walking parallel in the beep zone will not cause the collar to activate again. You have to walk in and then back out again to test.

Why is my underground fence not working?

Check for a break in the underground wiring of the invisible fence. Most invisible fence units register an error if there is a break in the fence. It should either flash red lights or set off an alarm. Remove the ends of the fence wire from the transmitter jacks and replace them with the ends of a spare piece of wire.

Can you splice dog fence wire?

When splicing the dog fence wire, all you need to do is twist the two exposed ends together, insert them into the gel-filled capsule and close the splice lock. The cylinder of the underground wire splice contains a mixture of silicone and grease, which helps to secure the waterproof connection.

How do you find a partial break in an invisible fence?

Plug in the Fence Transmitter and check the Loop Indicator Light. If the Loop Indicator Light is on you can assume the break is in the other half of the Boundary Wire. If the Loop Indicator Light did not come on and you hear a continuous beep, you may assume there is a break in this portion of the Boundary Wire.

How do you turn up an invisible shock fence?

Adjust the Power Level After checking the current level, press the button again within 5 seconds to raise the correction level. The collar will beep or blink in series to indicate the new shock level. Press the button again within 5 seconds to raise the level once more.

How long do PetSafe transmitters last?

The Wireless Containment System unit can last up to approximately 10 years or more if used properly. Batteries on the collar can last and be replaced up to 1 to 2 months.

How tight should a shock collar be?

The collar strap should be tight enough that the contact points are applying light pressure on your dog’s neck but it shouldn’t be able to slide or re-position itself on your pet’s neck. You may have to take a few minutes to get the right adjustment, but this step is very important when working with e-collars.

Why is bark collar not working?

Tighten the Bark Control Collar and/or trim your dog’s hair where the Contact Points touch his neck to ensure good skin contact. Replace the battery. If your dog still does not respond, contact the Customer Care Center at 1-800-732-2677. The Bark Control Collar Indicator Light is flashing.

Why is my dog's shock collar not working?

Make sure your battery is charged in both the collar and the transmitter. Low battery charge can make for inconsistent functioning. Make sure both pieces are turned on and that the unit is properly synced so that the collar is receiving a signal from the transmitter.

How do you test a dog shock collar?

1. Turn the Collar Receiver on.
2. Hold the Test Light Contacts to the Contact Points.
3. Press a Stimulation Button on the Remote Transmitter.
4. The Test Light will flash.
5. NOTE: At higher stimulation levels, the Test Light will flash brighter.
6. Turn the Collar Receiver off.