What does eo2 mean on lazy spa

The E02 error code can occur when the filters are dirty or blocked. SOLUTIONS WASH OR CHANGE THE FILTERS. Remove the filter cartridge from the filter housing. Using luke warm water, run the filter cartridge under the water until it runs clear.

What is error 02 on a lazy spa?

Is there an E02 error code displaying on your Lay-Z-Spa pump? This means your Lay-Z-Spa pump is experiencing a water flow issue. … To clean the filter cartridge use luke warm water, run the filter cartridge under the water until the water runs clear. Do not use any detergent, washing up liquid or other chemicals.

How do you fix lazy spa error code GCF?

Turn the pump off using the On/Off power button on the pump display. Remove the plug from the socket.
Plug the spa pump in to another socket (preferably inside your home if you have been trying with an outdoor socket)
Switch the pump on and press the reset/test on the cable.

How do you fix the error code on a hot tub?

Shut down the spa at the breaker.
Make sure there is no debris in the water that can get sucked into the pump.
Take out all of the filter(s) and set them aside.
Turn spa back on at the breaker with the filters out.

What does E02 error mean?

The E02 error code can occur when the filters are dirty or blocked. SOLUTIONS WASH OR CHANGE THE FILTERS. Remove the filter cartridge from the filter housing.

What does F8 mean on a hot tub?

Filtration Cycles run from F1 to F8 (F1 = 1 hour every 12 hours / F8 = 8 hours every 12 hours). Preset cycle set from factory is F1, so if in ec or sl mode your water will not reach desired temperature.

What does E02 mean on a washing machine?

E02 – the machine has failed to fill with water during its allocated time. Check the mains water pressure, by turning on the sink taps and checking for the usual pressure, if this is ok check the inlet hose for kinks, the pressure switch and inlet valve.

What are the codes on a hot tub?

CODEERROR CODE DESCRIPTIONCE 04Water sensor/pressure switch faultCE 05Temperature sensor, or water is dangerously hotCE 06High limit manual reset on heater is trippedCE 07Stuck heater relay

What does HFL mean on hot tub?

Balboa HFL, HL, or HTR FLOW LOW Error codes. The Balboa spa pack has detected this fault 5 times in the last 24 hours or less, and the heater is now disabled. This fault has typically occurred as a result of not enough water flow through the heater to carry the hot water away from the heating element.

How often should you change water in Lay Z Spa?

It is recommended that Lay‑Z‑Spa water is changed regularly, and at least once every 1‑3 months.

Article first time published on

Why does my lazy spa keep tripping?

Hot tub heaters can become corroded or damaged, resulting in a circuit breaker that keeps tripping when you want to use your hot tub. You might be able to notice signs of damage or corrosion in this part of your hot tub. If the heater does have damage, you might need to have it repaired or replaced.

Why is my lazy spa pump not working?

Unplug the spa pump from the electricity, wait 10 seconds then plug the spa back in. Reset the spa as first use using the reset button. Once reset, turn on the Hydro Jet system. … Allow the spa pump to run on either the 5 hour or 8 hour setting.

What is e03 On lazy spa?

This error code is visible if the ambient air temperature is too low outside. The spa pump will not run if the air temperature is below 4-6°c. Remove the pump from the spa by placing the stopper caps on the inside of the spa over the debris screens. … Once the spa pump has warmed up, the error code should disappear.

Why is water not going into my washing machine?

Water comes into your washing machine for the wash and rinse cycles through the water inlet valve. So a lack of water at the wash or rinse cycle could be a result of a broken water inlet valve. Unplug the washer, then use a multi-meter to verify that the solenoids to open the valve have continuity.

What does E02 mean on a Bosch washing machine?

Bosch Nexxt 500 series washer displays the E02 error code. It signals about problems with the electric motor of the device. In this case, the drum does not rotate when the washing program is run, or the program does not start at all.

What does ECN mean on a hot tub?

Ecn or Ec Message Ecn or Ec is Alternating with Temp: The Spa is Operating in the “Economy” (Ecn or Ec) Heating Mode. The Water Temperature is Sampled Only during Programmed Filter Cycles. The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles.

What does F3 mean on a hot tub?

Filter Cycles The filter program also controls how the spa heater operates as follows: • Standard filter programs (F0, F1, F2, F3): Heater activates anytime water temperature drops 2 degrees below the set temperature (Jets 1 low speed also activates on non-Circulation Pump models).

What is Dr code on hot tub?

Newer hot tubs have a digital display for error codes that can assist with troubleshooting. A message such as “dr” or “dry” or “heater dry” is a warning that there’s no water in the heater tube, says Niagara Hot Tubs. … If the water is low, add water to the proper level and try restarting the pump and heater.

What does HR mean on hot tub?

If you are seeing an HR code on your hot tub it means there is a hardware error on the motherboard that is not repairable. Try to reset the breaker but if that doesn’t work the pack will need to be replaced.

What is priming mode on a hot tub?

The purpose of the priming mode is to manually activate each spa pump prior to the automatic heat cycle being started. Typically, cycling each pump a few times will prime or purge any air from the plumbing. … That’s it, your hot tub is now full and ready for the next steps.

Does hot tub heat up faster with jets on?

A hot tub heats up faster if the jets are turned on. This is because the water circulates with the jets on, which evenly disperses heat and prevents cold water from being trapped in the hot tub pipes.

Are Lazy spas expensive to run?

Lay-Z-Spa is one of the cheapest hot tubs to run because of a number of additional features that make them the perfect hot tub for your home. Some of these features include: – EnergySense liner – Models that include this liner are 40% more energy efficient than other similar hot tubs.

How can I heat my hot tub faster?

Leave the cover on. …
Turn the jets on. …
Use a thermal spa blanket. …
Put a pop-up canopy tent around the tub. …
Wait for a warm day. …
Fill up with warm water. …
Use a portable immersion heater.

How many chlorine tablets do you put in a lazy spa?

How Many Chlorine Tablets? For smaller hot tubs we recommend 1-3 tablets and for larger hot tubs 3-5 tablets.

How often add chlorine to hot tub?

You should put chlorine in your hot tub at least once a week. However, some people prefer to add a small amount after each use. Finding the best water care routine will depend on how often and how many people use it. Chlorine levels should be between 1.5 and 3.0 ppm.

Should I leave lazy spa on all the time?

Leave Your Lay‑Z‑Spa Heater Activated Between Uses Depending on the amount you use your Lay‑Z‑Spa, in our experience it is better to leave the heater activated all of the time, if used regularly ‑ say 3 or more times per week.

Why am I getting an electric shock from the water in my hot tub?

You can get electrocuted in a hot tub. If electrical current is sent into the hot tub water as a result of faulty underwater lighting or wiring or ungrounded pumps or filters, then the electrified water can cause the electrical current to enter the bodies of anyone in the hot tub and electrocute them.

How long should a spa heater last?

The longevity of your hot tub is how long it will continue to work and last. The range of spas generally last anywhere from 5 to 20 years.

Can I plug my lazy spa into an extension lead?

Many inflatable hot tub manufacturers recommend against using an extension lead. This is likely to be for a number of reasons: Most DIY store extension leads use cable which is not sufficiently large in diameter (normally 1mmsq or 1.25mmsq) to handle the relatively high sustained current required. Most are rather long.

Why does the plug on my lazy spa get hot?

If your plug is hot to the touch, you should unplug the device immediately. There is a chance that the load the hot tub is placing exceeds the current carrying capacity of the circuit in your garage. So the hot tub may require 30 amps, but the wiring in your garage may be only suitable for a 15a circuit.

What fuse goes in a lazy spa plug?

There is also a 13A fuse in the plug, so if the load was 16A this would trip every time the spa is used.